Crown raising is the arboricultural practice of removing the lower branches of a tree to increase the clearance between the ground and the canopy. It's a common technique employed for a variety of reasons, from improving visibility and access under the tree to reducing interference with power lines or buildings. However, it's a practice that needs to be approached with care, as improper crown raising can significantly harm the tree's health and structural integrity.
Effective crown raising requires an understanding of tree biology and proper pruning techniques. One of the most important best practices is to avoid “lion's tailing.” This refers to removing too many inner branches, leaving only a tuft of foliage at the ends of the main branches. Lion's tailing weakens the branch structure, making it more susceptible to wind damage and breakage. It also reduces the tree's ability to photosynthesize effectively.
Another critical aspect is the amount of live crown removed. A general rule of thumb is to avoid removing more than 10-15% of the live crown in a single pruning session. Removing more than this can stress the tree, making it vulnerable to pests, diseases, and decline. For mature trees, even less should be removed. Furthermore, large pruning wounds should be avoided as they heal slowly and can become entry points for decay organisms. Cuts should be made just outside the branch collar, the slightly swollen area where the branch joins the trunk. This allows the tree to compartmentalize the wound and promotes faster healing.
The timing of crown raising is also important. While light pruning can be done at any time of year, more extensive crown raising is best performed during the dormant season, typically late fall or winter. This is because the tree is less active and the risk of disease transmission is lower. However, certain species, like maples and birches, are best pruned in summer after the leaves have fully developed to minimize sap bleeding.
Finally, hiring a qualified and certified arborist is highly recommended. They possess the knowledge and experience to assess the tree's condition, determine the appropriate pruning techniques, and execute the work safely and effectively. An arborist can also advise on the long-term management of the tree and help prevent future problems. Crown raising, when performed correctly, can enhance the beauty and functionality of a tree, but improper techniques can have detrimental effects. By following these best practices and seeking professional guidance, you can ensure the health and longevity of your trees.
Crown raising is a common tree pruning technique that involves removing the lower branches of a tree to increase clearance beneath the canopy. While it can offer benefits like improved visibility and access, it's crucial to prioritize safety, both for the arborist performing the work and for the long-term health of the tree.
For the arborist, proper safety equipment is paramount. This includes a helmet, eye protection, gloves, chainsaw chaps, and sturdy footwear. Depending on the height and complexity of the crown raising, a climbing harness, ropes, and a secure anchor point are essential. Before starting, the arborist should assess the surrounding area for hazards like power lines, buildings, or unstable ground. A clear drop zone for branches should be established, and communication with any nearby individuals is vital. Regular equipment inspections and proper climbing techniques are essential for minimizing the risk of falls and injuries.
The tree's health is also a major safety consideration. Over-raising the crown, removing too many branches at once, or making improper cuts can weaken the tree, making it more susceptible to disease, pests, and storm damage. Ideally, no more than one-third of the living crown should be removed during a single pruning session. Cuts should be made just outside the branch collar, avoiding flush cuts that can damage the trunk and hinder the tree's ability to compartmentalize the wound. Understanding tree biology and proper pruning techniques is crucial for preserving the tree's structural integrity and long-term health.
Finally, consider the post-pruning safety. Larger branches should be chipped or removed to prevent tripping hazards. The work area needs to be left clean and tidy. It's important to inform the tree owner about ongoing care, such as watering during dry periods, to help the tree recover from the pruning and maintain its health.
In conclusion, crown raising, while beneficial, requires careful consideration of safety for both the arborist and the tree. By prioritizing proper equipment use, adhering to sound pruning practices, and planning for post-pruning care, we can ensure the procedure is carried out safely and effectively, preserving the beauty and health of our trees for years to come.
Crown raising, while often beneficial for increasing light penetration and clearance, isn't without its potential problems. Understanding these issues and employing appropriate mitigation strategies is crucial for the long-term health and stability of the tree.
One common problem is excessive removal of live crown. Trees need their leaves for photosynthesis, and removing too many can weaken the tree, making it more susceptible to pests, diseases, and environmental stresses like drought. A good mitigation strategy is to limit crown raising to the minimum amount required for the desired objective. A qualified arborist should assess the tree and determine the appropriate amount of crown that can be safely removed, typically no more than 20% of the living crown at any one time. Staging the crown raising over several years can also help to minimize stress on the tree.
Another potential issue is the creation of large pruning wounds. These wounds can be entry points for decay organisms. Proper pruning techniques are essential to minimize the risk of decay. Cuts should be made just outside the branch collar, avoiding flush cuts that damage the trunk. Wound dressings are generally not recommended as they can interfere with the tree's natural compartmentalization process. Instead, focus on making clean, precise cuts to promote faster healing.
Improper pruning cuts can lead to the development of epicormic sprouts, also known as water sprouts. These are rapidly growing, weakly attached branches that arise from dormant buds near the pruning wounds. They are often unsightly and can be structurally unsound. Proper pruning techniques, as mentioned above, can help minimize their occurrence. If they do appear, they should be removed promptly while they are still small.
Finally, crown raising can alter the tree's natural form and potentially destabilize it, particularly in species prone to windthrow. Raising the crown too high can increase the tree's wind sail effect, making it more vulnerable to strong winds. Careful consideration of the tree's species, location, and prevailing wind patterns is crucial before undertaking crown raising. A qualified arborist can assess the potential risks and recommend appropriate strategies to minimize the chance of windthrow. This might include limiting the height of the crown raising or using cabling or bracing to provide additional support.
Crown raising, the practice of removing lower branches on a tree, can have significant long-term impacts on both its health and structure. While often employed for practical reasons like increasing clearance for vehicles or improving visibility, it's crucial to understand the potential consequences before undertaking such a procedure.
One major long-term effect is the creation of entry points for decay. Removing larger, lower branches creates wounds that, if not properly managed, can become susceptible to fungal and bacterial infections. These infections can spread throughout the tree, weakening its structure and potentially leading to premature decline or even failure. The location of these wounds is also critical. Lower branches typically have a wider base of attachment, offering more structural support. Removing them alters the tree's load distribution, potentially making it more vulnerable to wind damage in the long run.
Another consideration is the impact on the tree's energy reserves. Lower branches contribute significantly to photosynthesis, the process by which trees produce their food. Removing a substantial portion of these branches reduces the tree's ability to generate energy, potentially slowing its growth and making it more susceptible to stress from drought, pests, or disease. While trees can adapt to some degree, excessive crown raising can severely compromise their long-term health and vigor.
Furthermore, the aesthetics of the tree can be permanently altered. Excessive crown raising can result in an unnatural, lollipop-like appearance, diminishing its beauty and potentially reducing its value in a landscape setting. It's important to strike a balance between practical considerations and preserving the tree's natural form.
Finally, the specific species of tree plays a role in how it responds to crown raising. Some species are more tolerant of branch removal than others. For example, trees with rapid growth rates may recover more quickly, while slower-growing species may suffer more significant long-term consequences. Consulting with a certified arborist is crucial to assess the specific needs of your trees and determine the appropriate approach to crown raising, minimizing the potential for long-term negative impacts. Their expertise can help ensure that the procedure is carried out correctly, preserving the tree's health, structure, and aesthetic appeal for years to come.
An arborist, or (less commonly) arboriculturist, is a professional in the practice of arboriculture, which is the cultivation, management, and study of individual trees, shrubs, vines, and other perennial woody plants in dendrology and horticulture.[citation needed]
Arborists generally focus on the health and safety of individual plants and trees, rather than managing forests or harvesting wood (silviculture or forestry). An arborist's scope of work is therefore distinct from that of either a forester or a logger.[citation needed]
In order for arborists to work near power wires, either additional training is required or they need to be certified as a Qualified Line Clearance Arborist or Utility Arborist (there may be different terminology for various countries). There is a variety of minimum distances that must be kept from power wires depending on voltage, however the common distance for low voltage lines in urban settings is 10 feet (about 3 metres).[1]
Arborists who climb (as not all do) can use a variety of techniques to ascend into the tree. The least invasive, and most popular technique used is to ascend on rope. There are two common methods of climbing, Single Rope System (SRS) and Moving Rope System (MRS). When personal safety is an issue, or the tree is being removed, arborists may use 'spikes', (also known as 'gaffs' or 'spurs') attached to their chainsaw boots with straps to ascend and work. Spikes wound the tree, leaving small holes where each step has been.[citation needed]
An arborist's work may involve very large and complex trees, or ecological communities and their abiotic components in the context of the landscape ecosystem. These may require monitoring and treatment to ensure they are healthy, safe, and suitable to property owners or community standards. This work may include some or all of the following: planting; transplanting; pruning; structural support; preventing, or diagnosing and treating phytopathology or parasitism; preventing or interrupting grazing or predation; installing lightning protection; and removing vegetation deemed as hazardous, an invasive species, a disease vector, or a weed.[citation needed]
Arborists may also plan, consult, write reports and give legal testimony. While some aspects of this work are done on the ground or in an office, much of it is done by arborists who perform tree services and who climb the trees with ropes, harnesses and other equipment. Lifts and cranes may be used too. The work of all arborists is not the same. Some may just provide a consulting service; others may perform climbing, pruning and planting: whilst others may provide a combination of all of these services.[2]
Arborists gain qualifications to practice arboriculture in a variety of ways and some arborists are more qualified than others. Experience working safely and effectively in and around trees is essential. Arborists tend to specialize in one or more disciplines of arboriculture, such as diagnosis and treatment of pests, diseases and nutritional deficiencies in trees, climbing and pruning, cabling and lightning protection, or consultation and report writing. All these disciplines are related to one another and some arborists are very well experienced in all areas of tree work, however not all arborists have the training or experience to properly practice every discipline.[citation needed]
Arborists choose to pursue formal certification, which is available in some countries and varies somewhat by location. An arborist who holds certification in one or more disciplines may be expected to participate in rigorous continuing education requirements to ensure constant improvement of skills and techniques.[citation needed]
In Australia, arboricultural education and training are streamlined countrywide through a multi-disciplinary vocational education, training, and qualification authority called the Australian Qualifications Framework, which offers varying levels of professional qualification. Government institutions including Technical and Further Education TAFE offer Certificate III or a diploma in arboriculture as well as some universities.[3][4] There are also many private institutions covering similar educational framework in each state. Recognition of prior learning is also an option for practicing arborists with 10 or more years of experience with no prior formal training. It allows them to be assessed and fast track their certification.[citation needed]
In France, a qualified arborist must hold a Management of Ornamental Trees certificate, and a qualified arborist climber must hold a Pruning and Care of Trees certificate; both delivered by the French Ministry of Agriculture.[5][6]
In the UK, an arborist can gain qualifications up to and including a master's degree. College-based courses include further education qualifications, such as national certificate, national diploma, while higher education courses in arboriculture include foundation degree, bachelor's degree and master's degree.[citation needed]
In the US, a Certified Arborist (CA) is a professional who has over three years of documented and verified experience and has passed a rigorous written test from the International Society of Arboriculture. Other designations include Municipal Specialist, Utility Specialist and Board Certified Master Arborist (BCMA). The USA and Canada additionally have college-based training which, if passed, will give the certificate of Qualified Arborist. The Qualified Arborist can then be used to offset partial experience towards the Certified Arborist.
Tree Risk Assessment Qualified credential (TRAQ), designed by the International Society of Arboriculture, was launched in 2013. At that time people holding the TRACE credential were transferred over to the TRAQ credential.[citation needed]
In Canada, there are provincially governed apprenticeship programs that allow arborists' to work near power lines upon completion. These apprenticeship programs must meet the provincial reregulations (For example, in B.C. they must meet WorkSafeBC G19.30), and individuals must ensure they meet the requirements of the owner of the power system.[citation needed]
Trees in urban landscape settings are often subject to disturbances, whether human or natural, both above and below ground. They may require care to improve their chances of survival following damage from either biotic or abiotic causes. Arborists can provide appropriate solutions, such as pruning trees for health and good structure, for aesthetic reasons, and to permit people to walk under them (a technique often referred to as "crown raising"), or to keep them away from wires, fences and buildings (a technique referred to as "crown reduction").[7] Timing and methods of treatment depend on the species of tree and the purpose of the work. To determine the best practices, a thorough knowledge of local species and environments is essential.[citation needed]
There can be a vast difference between the techniques and practices of professional arborists and those of inadequately trained tree workers. Some commonly offered "services" are considered unacceptable by modern arboricultural standards and may seriously damage, disfigure, weaken, or even kill trees. One such example is tree topping, lopping, or "hat-racking", where entire tops of trees or main stems are removed, generally by cross-cutting the main stem(s) or leaders, leaving large unsightly stubs. Trees that manage to survive such treatment are left prone to a spectrum of detrimental effects, including vigorous but weakly attached regrowth, pest susceptibility, pathogen intrusion, and internal decay.[8]
Pruning should only be done with a specific purpose in mind. Every cut is a wound, and every leaf lost is removal of photosynthetic potential. Proper pruning can be helpful in many ways, but should always be done with the minimum amount of live tissue removed.[9]
In recent years, research has proven that wound dressings such as paint, tar or other coverings are unnecessary and may harm trees. The coverings may encourage growth of decay-causing fungi. Proper pruning, by cutting through branches at the right location, can do more to limit decay than wound dressing [10]
Chemicals can be applied to trees for insect or disease control through soil application, stem injections or spraying. Compacted or disturbed soils can be improved in various ways.[citation needed]
Arborists can also assess trees to determine the health, structure, safety or feasibility within a landscape and in proximity to humans. Modern arboriculture has progressed in technology and sophistication from practices of the past. Many current practices are based on knowledge gained through recent research, including that of Alex Shigo, considered one "father" of modern arboriculture.[11]
Depending on the jurisdiction, there may be a number of legal issues surrounding the practices of arborists, including boundary issues, public safety issues, "heritage" trees of community value, and "neighbour" issues such as ownership, obstruction of views, impacts of roots crossing boundaries, nuisance problems, disease or insect quarantines, and safety of nearby trees or plants that may be affected.[citation needed]
Arborists are frequently consulted to establish the factual basis of disputes involving trees, or by private property owners seeking to avoid legal liability through the duty of care.[12] Arborists may be asked to assess the value of a tree[13] in the process of an insurance claim for trees damaged or destroyed,[14] or to recover damages resulting from tree theft or vandalism.[15] In cities with tree preservation orders an arborist's evaluation of tree hazard may be required before a property owner may remove a tree, or to assure the protection of trees in development plans and during construction operations. Carrying out work on protected trees and hedges is illegal without express permission from local authorities,[16] and can result in legal action including fines.[17] Homeowners who have entered into contracts with a Homeowner's association (see also Restrictive covenants) may need an arborists' professional opinion of a hazardous condition prior to removing a tree, or may be obligated to assure the protection of the views of neighboring properties prior to planting a tree or in the course of pruning.[18] Arborists may be consulted in forensic investigations where the evidence of a crime can be determined within the growth rings of a tree, for example. Arborists may be engaged by one member of a dispute in order to identify factual information about trees useful to that member of the dispute, or they can be engaged as an expert witness providing unbiased scientific knowledge in a court case. Homeowners associations seeking to write restrictive covenants, or legislative bodies seeking to write laws involving trees, may seek the counsel of arborists in order to avoid future difficulties.[19]
Before undertaking works in the UK, arborists have a legal responsibility to survey trees for wildlife, especially bats, which are given particular legal protection. In addition, any tree in the UK can be covered by a tree preservation order and it is illegal to conduct any work on a tree, including deadwooding or pruning, before permission has been sought from the local council.[citation needed]
The protagonist in Italo Calvino's novel The Baron in the Trees lives life on the ground as a boy and spends the rest of his life swinging from tree to tree in the Italian countryside. As a young man he helps the local fruit farmers by pruning their trees.[citation needed]
Some noteworthy arborists include:
Pruning is a horticultural, arboricultural, and silvicultural practice involving the selective removal of certain parts of a plant, such as branches, buds, or roots.
The practice entails the targeted removal of diseased, damaged, dead, non-productive, structurally unsound, or otherwise unwanted plant material from crop and landscape plants. In general, the smaller the branch that is cut, the easier it is for a woody plant to compartmentalize the wound and thus limit the potential for pathogen intrusion and decay. It is therefore preferable to make any necessary formative structural pruning cuts to young plants, rather than removing large, poorly placed branches from mature plants.
Woody plants may undergo a process referred to as "self-pruning", where they will drop twigs or branches which are no longer producing more energy than they require. It is theorized that this process can also occur in response to lack of water, in order to reduce the surface area where water can be lost.[1] This natural shedding of branches is called cladoptosis.
Specialized pruning practices may be applied to certain plants, such as roses, fruit trees, and grapevines. Different pruning techniques may be used on herbaceous plants than those used on perennial woody plants.
Reasons to prune plants include deadwood removal, shaping (by controlling or redirecting growth), improving or sustaining health, reducing risk from falling branches, preparing nursery specimens for transplanting, and both harvesting and increasing the yield or quality of flowers and fruits.
Branch wood is an individual stem that grows off of another stem.
Trunk wood is the main stem of a tree which individual stems grow out of.
This refers to the area below the union of where branch wood attaches with the trunk/stem wood. This can often appear raised.
This refers to the junction between branch wood and trunk/stem wood. It usually looks raised. [2]
Pruning in an urban setting is crucial due to the tree being in drastically different conditions than where it naturally grows.[3]
Arborists, orchardists, and gardeners use various garden tools and tree cutting tools designed for the purpose, such as secateurs, loppers, handsaws, or chainsaws.[4] Additionally in forestry, pole pruners (averruncators in British English) and pole saws are commonly used, and these are often attached to poles that reach up to 5–6 m (16–20 ft). This is a more efficient and safer way of pruning than with ladders. These bush saws on polls have also been motorized as chainsaws which is even more efficient. Older technology used Billhooks, Kaiser blades, and pruning knives. Although still used in some coppicing, they are not used so much in commercial forestry due to the difficulty of cutting flush with the stem. Flush cuts happen when a pruner cuts into the cambium layer of the main trunk, which can happen when a pruner is not precise with pruning cuts, and removes a portion of the branch collar, which can put the tree at risk of entry cords from forest pathogens.
Although there are several different types of pruning, they can be simplified into two categories. One of which is cutting the branch back to a specific and intermediate point, called a "reduction cut", and the other of which is completely removing a branch back to the union where the branch connects which the main trunk, called "removal cut".[5]
A "reduction cut" is when one removes a portion of a growing stem down to a set of desirable buds or side-branching stems. This is commonly performed in well trained plants for a variety of reasons, for example to stimulate growth of flowers, fruit or branches, as a preventive measure to wind and snow damage on long stems and branches, and finally to encourage growth of the stems in a desirable direction.
In orchards, fruit trees are often lopped to encourage regrowth and to maintain a smaller tree for ease of picking fruit. The pruning regime in orchards is more planned, and the productivity of each tree is an important factor.
Branches die off for a number of reasons including sunlight deficiency, pest and disease damage, and root structure damage. A dead branch will at some point decay back to the parent stem and fall off. This is normally a slow process but can be hastened by high winds or extreme temperatures. The main reason deadwooding is performed is safety. Situations that usually demand removal of deadwood include trees that overhang public roads, houses, public areas, power lines, telephone cables and gardens. Trees located in wooded areas are usually assessed as lower risk but assessments consider the number of visitors. Trees adjacent to footpaths and access roads are often considered for deadwood removal.[8]
Another reason for deadwooding is amenity value, i.e. a tree with a large amount of deadwood throughout the crown will look more aesthetically pleasing with the deadwood removed. The physical practice of deadwooding can be carried out most of the year though should be avoided when the tree is coming into leaf. The deadwooding process speeds up the tree's natural abscission process. It also reduces unwanted weight and wind resistance and can help overall balance.
Preventative and structural pruning can be done to mitigate several issues young trees may have in the future. The structural pruning can reduce tree stress, increase the lifespan of trees, and promotes resistance to damage due to natural weather events. Attributes of trees with good structure include excurrent growth by having a single dominant leader, branch unions without included bark, and a balanced canopy. Structural pruning does this by developing or maintaining a dominant leader, identify the lowest branches in the canopy, prevent branches below the permanent canopy from growing too large, keeping all branches less than one half the trunk diameter, space main branches along one dominant trunk, and suppress growth on branches with included bark. [9]
Subordination pruning is done on limbs that will exceed 50% percent of the stem diameter. A reduction cut may be performed while still allowing about 50% of the branch. This is done to help maintain form and deter the formation of co-dominant leaders. Temporary branches may be too large for a removal cut so subordination pruning should be done to slowly reduce a limb by 50% each year to allow the tree to properly heal from the cut. As a tree becomes larger the slower it grows. Reducing the larger limbs for eventual removal will allow for the tree to promote new growth rather than using energy in encouraging unwanted limbs to continue to grow. Removing a large branch increases the likelihood of the cut to not heal properly which also may attract insects, diseases and fungus. [9][10]
Crown thinning is the removal of live healthy branches which increases light penetration, air circulation and reduces wind resistance which reduces risks from damage and the possibility of pest infestation. [11]
Crown raising involves the removal of the lower branches to a given height. The height is achieved by the removal of whole branches or removing the parts of branches which extend below the desired height. The branches are normally not lifted to more than one third of the tree's total height.
Crown lifting is done for access; these being pedestrian, vehicle or space for buildings and street furniture. Lifting the crown will allow traffic and pedestrians to pass underneath safely. This pruning technique is usually used in the urban environment as it is for public safety and aesthetics rather than tree form and timber value.
Crown lifting introduces light to the lower part of the trunk; this, in some species can encourage epicormic growth from dormant buds. To reduce this sometimes smaller branches are left on the lower part of the trunk. Excessive removal of the lower branches can displace the canopy weight, this will make the tree top heavy, therefore adding stress to the tree. When a branch is removed from the trunk, it creates a large wound. This wound is susceptible to disease and decay, and could lead to reduced trunk stability. Therefore, much time and consideration must be taken when choosing the height the crown is to be lifted to.
This would be an inappropriate operation if the tree species’ form was of a shrubby nature. This would therefore remove most of the foliage and would also largely unbalance the tree. This procedure should not be carried out if the tree is in decline, poor health or dead, dying or dangerous (DDD) as the operation will remove some of the photosynthetic area the tree uses. This will increase the decline rate of the tree and could lead to death.
If the tree is of great importance to an area or town, (i.e. veteran or ancient) then an alternative solution to crown lifting would be to move the target or object so it is not in range. For example, diverting a footpath around a tree's drip line so the crown lift is not needed. Another solution would be to prop up or cable-brace the low hanging branch. This is a non-invasive solution which in some situations may be more economical and environmentally friendly. [12]
Selectively pruning a window of view in a tree.
Reducing the height and or spread of a tree by selectively cutting back to smaller branches and in fruit trees for increasing of light interception and enhancing fruit quality.
A regular form of pruning where certain deciduous species are pruned back to pollard heads every year in the dormant period. This practice is usually commenced on juvenile trees so they can adapt to the harshness of the practice. This practice can be used for tree shaping but is also used in specific species which young branches can be sold for floral arrangements.
Deadheading is the act of removing spent flowers or flowerheads for aesthetics, to prolong bloom for up to several weeks or promote rebloom, or to prevent seeding.
In general, pruning deadwood and small branches can be done at any time of year. Depending on the species, many temperate plants can be pruned either during dormancy in winter, or, for species where winter frost can harm a recently pruned plant, after flowering is completed. In the temperate areas of the northern hemisphere autumn pruning should be avoided, as the spores of disease and decay fungi are abundant at this time of year.
Some woody plants tend to bleed profusely from cuts, such as mesquite and maple. Some callus over slowly, such as magnolia. In this case, they are better pruned during active growth when they can more readily heal. Woody plants that flower early in the season, on spurs that form on wood that has matured the year before, such as apples, should be pruned right after flowering as later pruning will sacrifice flowers the following season. Forsythia, azaleas and lilacs all fall into this category.